You should not need anything more than basic automotive hand tools and a little bit of mechanical ability. Take a look at the parts when you get the package and you should be able to see how it goes together. If not, feel free to write back or give Customer Service a call and we will get you squared away, but I doubt you will have trouble with it. view full answer...
The Aries # AA204009 Round Nerf Bars attach to the vehicle using the existing body mount bolts and brackets that are included with the bars. All the necessary installation hardware is provided.
On that model year, be aware that GM used a very strong thread locker on those body mount bolts so using air tools isn't recommended and can damage the bolts or the internal nut assembly. Hand tools are recommended. When the bolt is reinstalled, it's recommended that you use some anti-seize on the... view full answer...
Yes you should torque the bolts down properly with a torque wrench. Torque wrenches can be found at any store that carries a good selection of automotive tools.
The torque rating for the bolts with this hitch, currently, are listed for 76 Lb.-Ft. This number can change if the manufactuerer changes hardware or if Mazda were to adjust the frame, so always check the instructions included with the hitch for torque rating. view full answer...
The Curt Trailer Hitch Receiver, part # 13455 only requires basic tools to be installed on your 2002 Land Rover Discovery and does not require you to drill any holes.
You will need an open-ended wrench, and a ratcheting wrench with socket sizes of 14mm, 7/16 inches, and 5/8 inches. To make sure all hardware is snug and tight you will also need a torque wrench to torque all the bolts down to specified torque requirements in the instructions. If you do not have a torque wrench, you should... view full answer...
In order to show you how to remove and replace the lens on the Optronics Pedestal Mount 3-Function Trailer Light ST51RB I pulled one from our warehouse. For reference, this light uses replacement incandescent bulb 2057, available at automotive supply stores.
If you refer to the linked video you will see that we found the best way to remove the lens was to use a pry tool. In this case we chose to use a plastic bottle opener since its less likely to damage the lens than a steel screwdriver... view full answer...
Properly torquing down the hitch bolts is necessary to the proper function of the hitch as well as preventing damage to the vehicle.
Toyota provided weld-nuts inside the frame to make installation easier. But, they will break free if over-tightened and an average adult male can exert in the neighborhood of 60-70 ft.-lbs. with a 1/2 inch drive socket wrench.
Auto parts stores often rent specialty automotive tools and they may rent torque wrenches. You could also tighten the hitch down... view full answer...
If you are installing just the Firestone Ride-Rite airbags # F2255 without an on-board air compressor like the # F2158, then I would estimate that it should take about 2 hours to install the kit. This estimate is for someone with some mechanical ability, all of the proper tools and automotive experience working at home in the driveway or garage, plus having someone around to help.
A professional may take less time depending on how many similar installations they have done. Individual results... view full answer...
Apparently this was a known issue because Timbren put a couple of notes in the instructions regarding the use of penetrating oil to remove the fasteners for the OEM hardware and, if the factory nut is damaged, to use the supplied fastener. This indicates that this is a common issue on these trucks.
More than likely the OEM nut is damaged and doesn't necessarily require a special tool but will require cutting away the nut to remove the bump stop. If that is not something you are ready... view full answer...
It sounds like you're asking about the installation of a Curt hitch on your 2019 Toyota Corolla. I'll start by confirming for you that the Curt # C11265 hitch is a fit on your 2019 Toyota Corolla. This hitch installs without any drilling required, so it's likely something that you could complete on your own, with a few basic hand tools. I've linked an installation video of this hitch on a vehicle like yours for you to have a look at and follow along with if you'd like to do it yourself-... view full answer...
What you can do is apply something like Liquid Electrical Tape, # SWC50122, which will insulate, seal, and waterproof electrical connections. I would still recommend wrapping any connections with actual electrical tape as well for extra protection.
Another option is to use heat shrink tubing which is usually available just about anywhere tools and/or automotive parts are sold. With this you would first place the tubing around one of the wires before making the connection. Then use a butt... view full answer...
The Waterproof, Over 80 inch Aero Pro Trailer Light Kit, # TL16RK, does contain the hardware needed for installation, but the lights and housing themselves are what is considered waterproof; they are sealed lights. The electrical connections for the wires are not waterproof.
What you can do is apply something like Liquid Electrical Tape, # SWC50122, which will insulate, seal, and waterproof electrical connections. I would still recommend wrapping any connections with actual electrical... view full answer...
We usually gauge trailer hitch installation difficulty by how long it takes to install the hitch. This hitch requires that the exhaust be temporarily lowered and that a heat shield be modified or trimmed so the hitch will fit. We estimate that if you have all the proper tools and another person to help, it will take about 50 minutes to install the Curt Trailer Hitch, # 11372. If you have some automotive experience, this installation will be mildly difficult. I have included a link to the... view full answer...
Go To Results